©2002, INPRO Development Corporation
 
 FAQFAQ   ПоискПоиск   ПользователиПользователи   ГруппыГруппы   РегистрацияРегистрация
 ПрофильПрофиль   Войти и проверить личные сообщенияВойти и проверить личные сообщения   ВходВход

Посмотрите диагностику плиииииз

 
Начать новую тему   Ответить на тему    Список форумов Форум по модемам IDC -> General
Предыдущая тема :: Следующая тема  
Автор Сообщение
Виктор2003
Junior member


Зарегистрирован: 15.02.2003
Сообщения: 1

СообщениеДобавлено: Сб Фев 15, 2003 4:07 am    Заголовок сообщения: Посмотрите диагностику плиииииз Ответить с цитатой

Crying or Very sad Через 5 минут выбивает постоянно.
Подскажите что делать. Sad

Inpro IDC 2814/5614 BXL/VR Diagnostics, Version 1.0.1.30
15.02.2003 4:03:09 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:04:34
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 26400/26400/26400/26400 bps
Rx Rate (Last/Init/Min/Max).. 38667/40000/38667/42667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 126
Tx/Power Drop/Rx Level....... 15/1/NA
SNR Last/Min/Max............. 39/39/43
Highest Rx/Tx State.......... 67/67
EQM Sum...................... 00EE
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 4/0/0
Renegs Issued/Granted........ 4/0
FForwards/FBacks/Denied...... 4/3/0
Forced FB/FB after FF/MaxREJ. 0/2/1
Last dialed number........... PXXXXXXX
V90 9481834347EB

Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 126/12/127
EQM Hits..................... 0
EQM Last 10 Readings......... 125 127 126 127 123 125 20 15 13 14
Last Retrain/Reneg Status.... Local Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 0 minutes ago
Handshake Time/Retries....... 26 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 0
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,8
Last Rx/Tx State............. 21/20
Energy at 3750Hz/Average .... 2321/1141
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 38667 bps (Reg.S120=9)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Unknown
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. V34 Codex WA/V34 Stuck Phase2
Workaround Used.............. ABCODE check (Machine Gun Noise)
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/5
Frames Errors, Rx/Tx......... 5/0 (0,3%/0,0%)
Frames Count, Rx/Tx.......... 1652/1078
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 20
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 323644
Characters Sent.............. 94937
Average CPS, Rx/Tx........... 1181/346
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 91



При строке s17=50 s11=50 s103=2

Inpro IDC 2814/5614 BXL/VR Diagnostics, Version 1.0.1.30
15.02.2003 4:16:07 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:04:06
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 19200/26400/19200/26400 bps
Rx Rate (Last/Init/Min/Max).. 29333/38667/29333/44000 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 83
Tx/Power Drop/Rx Level....... 15/3/NA
SNR Last/Min/Max............. 41/37/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 011A
RBS Pattern.................. 00
Rate Drop.................... 0
Digital Loss................. 2000
Retrains Issued/Granted/Auto. 6/0/0
Renegs Issued/Granted........ 3/1
FForwards/FBacks/Denied...... 2/7/0
Forced FB/FB after FF/MaxREJ. 0/1/7
Last dialed number........... PXXXXXXX
V90 9481834347EB

Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 83/11/127
EQM Hits..................... 0
EQM Last 10 Readings......... 104 104 127 127 122 122 116 126 127 107
Last Retrain/Reneg Status.... Local Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 26 seconds/0
Non-linear Encoding, Rx/Tx... OFF/ON
Precoding, Rx/Tx............. OFF/ON
Shaping, Rx/Tx............... OFF/ON
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 1
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,8
Last Rx/Tx State............. 21/20
Energy at 3750Hz/Average .... 1900/935
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... Yes
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,0
V.90 Optimal Speed........... 30667 bps (Reg.S120=3)
V.8 Negotiation Started...... Yes
V.8bis Success............... No
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/No/Yes
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 03
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... Internal
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. V34 Codex WA/V34 Stuck Phase2
Workaround Used.............. ABCODE check (Machine Gun Noise)
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/27
Frames Errors, Rx/Tx......... 27/0 (2,0%/0,0%)
Frames Count, Rx/Tx.......... 1348/642
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 0
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 187776
Characters Sent.............. 64108
Average CPS, Rx/Tx........... 763/260
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 93
Вернуться к началу
Посмотреть профиль Отправить личное сообщение Отправить e-mail
Vlad
Associated member


Зарегистрирован: 24.12.2002
Сообщения: 10

СообщениеДобавлено: Сб Фев 15, 2003 5:10 pm    Заголовок сообщения: Ответить с цитатой

а номер телефона случаем не 7454045 (CNT)? У меня сегодня с ними связь тоже разладилась, хотя обычно 53-54k:

Inpro IDC 2814/5614 BXL/VR Diagnostics, Version 1.0.1.30
15.02.2003 17:01:47 - Outbound Call by RemoteAccess
--------------------------------------------------------
Modem type: IDC-5614BXL/VR+ (Plus) Firmware revision: V2.23

Time Online.................. 00:02:12
Termination Reason........... RETRAIN FAILURE
Tx Rate (Last/Init/Min/Max).. 28800/26400/26400/28800 bps
Rx Rate (Last/Init/Min/Max).. 54667/53333/52000/54667 bps
Modulation................... V.90
Protocol/Compression......... LAP-M/V.42bis
Line Quality................. 77
Tx/Power Drop/Rx Level....... 15/1/NA
SNR Last/Min/Max............. 43/43/43
Highest Rx/Tx State.......... 67/87
EQM Sum...................... 0067
RBS Pattern.................. 00
Rate Drop.................... 2
Digital Loss................. 235F
Retrains Issued/Granted/Auto. 0/0/1
Renegs Issued/Granted........ 4/0
FForwards/FBacks/Denied...... 2/2/0
Forced FB/FB after FF/MaxREJ. 0/0/3
Last dialed number........... T7454045
V90 9481834246E0

Symbol Rate.................. 3200
Carrier Frequency Hz, Tx..... 1829
EQM Value (Last/Min/Max)..... 77/20/127
EQM Hits..................... 0
EQM Last 10 Readings......... 85 127 127 117 113 25 30 28 26 27
Last Retrain/Reneg Status.... Local Fast Retrain
Last Retrain/Reneg Reason.... Local Fallback due to High EQM
Last Retrain/Reneg Time...... 1 minutes ago
Handshake Time/Retries....... 22 seconds/0
Non-linear Encoding, Rx/Tx... OFF/OFF
Precoding, Rx/Tx............. OFF/OFF
Shaping, Rx/Tx............... OFF/OFF
Trellis Encoding, Tx......... 16 state
Pre-Emphasis Index, Tx....... 6
Band Edges Lower/Upper, Hz... 150/3825
Round trip delay, ms......... 4,8
Last Rx/Tx State............. 21/20
Energy at 3750Hz/Average .... 3927/2638
Auto Gain Amplitude, db...... 10
Detection of 120 Hz Tones.... No
Detection of Dual PCM........ No
V.90 RBS Pattern............. 00
V.90 Alternating RBS Pattern. 00
V.90 Digital Pad Value, db... 0,9
V.90 Optimal Speed........... No Limit (Reg.S120=0)
V.8 Negotiation Started...... Yes
V.8bis Success............... Yes
V.8bis CRe,CRd,CL,MS,ACK,NAK. Yes/No/Yes/No/Yes/No
Remote Manufacturer.......... Rockwell (Conexant)
Remote Licensee Code......... Rockwell (Conexant)
Remote Protocol Support...... K56flex V.90
Remote K56flex Version....... 02
Remote K56flex Capabilities.. Prototype mode is not supported
Remote Type.................. Server (Digital)
Remote supports Symbol Rates. 2743 2800 3429 3000(L) 3000(H)
Remote supports Symbol Rates. 3200(L) 3200(H) 3429(Tx)
Remote supports Power Drop... Yes
Remote is CME Modem.......... No
Remote supports V.34bis...... Yes
Remote Max SR Difference..... 0 Symbol Rate Steps
Remote Frequency Source...... External
Workaround Used.............. V90 Phase 2 Escape
Workaround Used.............. Rate Reneg Failure (At 64 or 84)
Workaround Used.............. V34 Codex WA/V34 Stuck Phase2
Error Correction Status Byte. SYNC UA:R SAMBE:T XID:T XID:R
Frames REJected, Last/Total.. 0/13
Frames Errors, Rx/Tx......... 13/0 (0,7%/0,0%)
Frames Count, Rx/Tx.......... 1931/789
Error Control Frame Size..... V.42 LAPM (128)
Error Control Timeouts....... 6
Error Control Link NAKs...... 0
Compression Dictionary Size.. V.42bis (2048)
Characters Received.......... 347930
Characters Sent.............. 111974
Average CPS, Rx/Tx........... 2635/848
Characters Lost, Rx/Tx....... 0/0
Estimated Noise Level, -dBm.. 95
Вернуться к началу
Посмотреть профиль Отправить личное сообщение
Показать сообщения:   
Начать новую тему   Ответить на тему    Список форумов Форум по модемам IDC -> General Часовой пояс: GMT + 3
Страница 1 из 1

 
Перейти:  
Вы не можете начинать темы
Вы не можете отвечать на сообщения
Вы не можете редактировать свои сообщения
Вы не можете удалять свои сообщения
Вы не можете голосовать в опросах


Powered by phpBB © 2001, 2005 phpBB Group

Created this page in 0.029741 seconds : 17 queries executed : GZIP compression enabled : Debug Mode

©2002, INPRO Development Corporation

Rambler's Top100